Alignement Grizzly 700

Tout sur les Yamaha
Post Reply
BIZOU
Posts: 1583
Joined: March 13, 2007, 5:35 pm
VTT: Grizzly 700
Location: Je ne sais pas, je suis trop soûl pour savoir où je suis............................................
Contact:

Alignement Grizzly 700

Post by BIZOU »

Je trouve nul part les " spec " du 700 pour l`alignement de la direction, fermé ou ouvert, et combien de milimêtres...........

peut-être que le 660 est le même ?

Merci


Une biere couvre 1% des besoins journaliers en vitamine C, B2 et B1, il faut donc boire 100 bières par jour pour avoir une alimentation équilibrée!!!

Au ciel il n`y a pas de bière, alors j`en profite sur terre.

http://www.apsq.ca
Kujo
Posts: 170
Joined: November 16, 2005, 1:05 pm
Location: Ste-Marthe-sur-le-lac, Qc

Post by Kujo »

Si tu as le "shop manual" du Grizzly 700, tu peux retrouver cette information à la page 3-59.

Ils spécifient que le "toe-in" doit être entre 0mm et 10mm (les pneus doivent toucher le sol, ne pas soulever le vtt lorsque tu mesures...).

Sur le schéma suivant (vue de haut du vtt), le "toe-in" est calculé en fesant B - A. La flèche près du C indique le devant du vtt.

Image

Donc tes roues avant doivent être soit parfaitement parralèles, soit légèrement entrées vers l'intérieur dans la partie avant du vtt.
Kujo
Grizzly 700 2007
Grizzly 660 Limited Edition 2003 (vendu)
Grizz007

réponse

Post by Grizz007 »

ADJUSTING THE TOE-IN ADJ
EBS00108
ADJUSTING THE TOE-IN
1. Place the vehicle on a level surface.
2. Measure:
• toe-in
Out of specification → Adjust.

NOTE: _
Before measuring the toe-in, make sure that
the tire pressure is correct.
a. Mark both front tire tread centers.
b. Face the handlebar straight ahead.
c. Measure the width È between the marks.
d. Rotate the front tires 180° until the marks
are exactly opposite one another.
e. Measure the width É between the marks.
f. Calculate the toe-in using the formula given
below.
g. If the toe-in is incorrect, adjust it.
Ê Forward

3. Adjust:
• toe-in
WARNING
_
• Be sure that both tie-rods are turned the
same amount. If not, the vehicle will drift
right or left even though the handlebar is
positioned straight. This may lead to mishandling
and an accident.
• After setting the toe-in to specification,
run the vehicle slowly for some distance
with both hands lightly holding the handlebar
and check that the handlebar
responds correctly. If not, turn either the
right or left tie-rod within the toe-in specification.

a. Mark both tie-rods ends.
This reference point will be needed during
adjustment.
Toe-in
0 ~ 10 mm (0 ~ 0.39 in)
(with tires touching the ground)
Toe-in = É – È
3 - 60
CHK
ADJ
ADJUSTING THE TOE-IN/CHECKING THE FRONT AND
REAR SHOCK ABSORBERS
b. Loosen the locknuts (tie-rod end) 1 of both
tie-rods.
c. The same number of turns should be given
to both the right and left tie-rods 2 until the
specified toe-in is obtained. This is to keep
the length of the rods the same.
d. Tighten the rod end locknuts of both tie
rods.
NOTE:
_
Adjust the rod ends so that A and B are equal.

T R . .
Locknut (rod end)
15 Nm (1.5 m · kg, 11 ft · lb)
1 1
2 2
EBS00109
CHECKING THE FRONT AND REAR SHOCK
ABSORBERS
1. Place the vehicle on a level place.
2. Check:
• damper rod
Bends/damage → Replace the front/rear
shock absorber assembly.
Refer to “FRONT ARMS AND FRONT
SHOCK ABSORBER ASSEMBLIES” and
“REAR ARMS AND REAR SHOCK
ABSORBER ASSEMBLIES” in chapter 8.
• oil leakage
Excessive oil leakage → Replace the front/
rear shock absorber assembly.
Refer to “FRONT ARMS AND FRONT
SHOCK ABSORBER ASSEMBLIES” and
“REAR ARMS AND REAR SHOCK
ABSORBER ASSEMBLIES” in chapter 8.
• spring
Fatigue → Replace the front/rear shock
absorber assembly.
Refer to “FRONT ARMS AND FRONT
SHOCK ABSORBER ASSEMBLIES” and
“REAR ARMS AND REAR SHOCK
ABSORBER ASSEMBLIES” in chapter 8
BIZOU
Posts: 1583
Joined: March 13, 2007, 5:35 pm
VTT: Grizzly 700
Location: Je ne sais pas, je suis trop soûl pour savoir où je suis............................................
Contact:

Post by BIZOU »

Merci Kujo. Je n`ai pas le shop manual encore.
Merci Grizz007.
Une biere couvre 1% des besoins journaliers en vitamine C, B2 et B1, il faut donc boire 100 bières par jour pour avoir une alimentation équilibrée!!!

Au ciel il n`y a pas de bière, alors j`en profite sur terre.

http://www.apsq.ca
Blondin
Posts: 449
Joined: June 7, 2004, 8:17 am
VTT: KLR 650
Location: Grand-Mère

Voila

Post by Blondin »

BIZOU wrote:Merci Kujo. Je n`ai pas le shop manual encore.
Merci Grizz007.

Suis ce lien http://www.megaupload.com/fr/?d=72VB6HYR
Normand " Blondin" Fortin
Outlander 800 XTP 2011
Amateur de VTT et de Chasse
BIZOU
Posts: 1583
Joined: March 13, 2007, 5:35 pm
VTT: Grizzly 700
Location: Je ne sais pas, je suis trop soûl pour savoir où je suis............................................
Contact:

Post by BIZOU »

Un gros merci Blondin,

comme ça m`a pouvoir laisser le monde tranquille avec mes questions ;-)
Une biere couvre 1% des besoins journaliers en vitamine C, B2 et B1, il faut donc boire 100 bières par jour pour avoir une alimentation équilibrée!!!

Au ciel il n`y a pas de bière, alors j`en profite sur terre.

http://www.apsq.ca
Post Reply

Return to “Yamaha”