D01
Throttle angle
• Fully closed position 15 ~ 20 Check with throttle fully closed.
• Fully opened position 95 ~ 100 Check with throttle fully open.
D03
Pressure difference (atmospheric pressure and intake air pressure).
Displays the intake air pressure. Set the engine stop switch to "RUN", then operate the throttle while pushing the start switch. (If the display value changes, the performance is OK.)
D05
Intake air temperature.
Displays the intake air temperature. Compare the actually measured intake air temperature with the meter.
D06
Coolant temperature.
Displays the coolant temperature. Compare the actually measured coolant temperature with the meter.
D07
Vehicle speed pulse 0 ~ 999
Check that the number increases when the rear wheel is rotated. The number is cumulative and does not reset each time the wheel is stopped.
D08
Lean angle sensor Remove the lean angle sensor and...
• Upright 0.4 ~ 1.4 incline it more than 65 degrees.
• Overturned 3.7 ~ 4.4
D09
Fuel system voltage (battery voltage): Approximately 12.0
Set the engine stop switch to "RUN", and then compare with the actually measured battery voltage. (If the battery voltage is lower, perform recharging).
D21
Neutral switch Shift the transmission.
• Neutral ON
• In gear OFF
D60
EEPROM fault code display.
• No history 00
• History exists 01
D61
Malfunction history code display.
• No history 00
• History exists Fault codes 12-50
• (If more than one code number is detected, the display alternates every two seconds to show all the detected code numbers. When all code numbers are shown, the display repeats the same process.)
D62
Malfunction history code erasure.
• No history 0 —
• History exists Up to 16 fault codes To erase the history, set the engine stop switch to "OFF" and then to
"RUN".
D70
Control number 00 ~ 255
Description des codes du module eletronique du 700FI
-
Le Kan Gourou
- Posts: 13106
- Joined: April 29, 2003, 12:21 am
- VTT: AC Cruiser 2011
- Location: Anjou et Ste-Mélanie Lanaudière
Description des codes du module eletronique du 700FI

2011 TRV Cruiser 1000 2000km
2008 Grizzy700 22000km
2007 Grizzly700 15000km
2004 TwinPeaks700 14000km
2001 QuadMaster500 3000km
-
Grizz007
plus de code
Diagnostic code table
Fault
code No.
Symptom Probable cause of malfunction Diagnostic code No.
12
No normal signals are received from
the crankshaft position sensor.
• Open or short circuit in wire harness.
• Defective crankshaft position sensor.
• Malfunction in pickup rotor.
• Malfunction in ECU.
• Improperly installed sensor.
—
13
Intake air pressure sensor: open or
short circuit detected.
• Open or short circuit in wire harness.
• Defective intake air pressure sensor.
• Malfunction in ECU.
D03
14
Intake air pressure sensor: hose system
malfunction (clogged or detached
hose).
• Intake air pressure sensor hose is detached, clogged,
kinked, or pinched.
• Malfunction in ECU.
D03
15
Throttle position sensor: open or short
circuit detected.
• Open or short circuit in wire sub lead.
• Open or short circuit in wire harness.
• Defective throttle position sensor.
• Malfunction in ECU.
• Improperly installed throttle position sensor.
D01
16
Stuck throttle position sensor
detected.
• Stuck throttle position sensor.
• Malfunction in ECU.
D01
21
Coolant temperature sensor: open or
short circuit detected.
• Open or short circuit in wire harness.
• Defective coolant temperature sensor.
• Malfunction in ECU.
• Improperly installed coolant temperature sensor.
D06
22
Intake air temperature sensor: open
or short circuit detected.
• Open or short circuit in wire harness.
• Defective intake air temperature sensor.
• Malfunction in ECU.
• Improperly installed intake air temperature sensor.
D05
30 The vehicle has overturned.
• Overturned.
• Malfunction in ECU.
D08
33
Malfunction detected in the primary
lead of the ignition coil.
• Open or short circuit in wire harness.
• Malfunction in ignition coil.
• Malfunction in ECU.
• Malfunction in a component of ignition cut-off circuit system.
D30
D32
39 Open circuit detected in a injector.
• Open or short circuit in wire harness.
• Improperly installed injector.
• Defective injector.
D36
41
Lean angle sensor: open or short circuit
detected.
• Open or short circuit in wire harness.
• Defective lean angle sensor.
• Malfunction in ECU.
D08
42
No normal signals are received from
the speed sensor.
• Open circuit in wire harness.
• Defective speed sensor.
• Malfunction in vehicle speed sensor detected.
• Malfunction in the engine side of the neutral switch.
• Malfunction in ECU.
D07
43
Power supply to the injector and fuel
pump is not normal.
• Open or short circuit in wire harness.
• Malfunction in ECU.
D09
44
Error is detected while reading or writing
on EEPROM (CO adjustment
value).
• Malfunction in ECU. (The CO adjustment value is not
properly written on or read from the internal memory).
D60
46
Power supply to the fuel injection system
is not normal.
• Malfunction in the charging system. Refer to “CHARGING
SYSTEM” in chapter 9.
—
50
Faulty ECU memory. (When this malfunction
is detected in the ECU, the
fault code number might not appear
on the LCD of the meter.)
• Malfunction in ECU. (The program and data are not
properly written on or read from the internal memory.)
—
-
yohann beauchamp
- Posts: 44
- Joined: February 18, 2007, 5:19 pm
- Location: st lin laurentides