Rod end kingquad
-
king 700
- Posts: 95
- Joined: January 22, 2005, 4:12 pm
Rod end kingquad
Bonjour j'aimerais savoir si quelqu'un a eu des problemes avec les rods end car moi je les trouve pourie mon kingquad 700 a 2000km et les rod end sont scrap ils ont 5 milieme de lousse sur chaque . j'ai regardé pour poser des rod end de vinson mais cela a l'air trop compliquer.J'aimerais avoir vos commentaire je sais que sur le site de nyroc's ATV il en parle des rod end mais je ne sais pas asser lire en anglais.
Merci.
Merci.
-
démon rouge
- Posts: 440
- Joined: February 14, 2005, 11:17 am
- Location: St-Eustache
rode de k.q.
mopi j'ai changé la celle de droite a 500 km.le dealer m'en as donné une autre et je l'ai allongé de un demie pouce ce qui me donne un quart de fillage de plus dans la tie rod end
demon rouge
demon rouge
-
Pascal la Dalle
- Posts: 758
- Joined: September 16, 2005, 9:42 pm
- VTT: ranger 800 xp
- Location: Dupuy
-
Homer
- Posts: 3030
- Joined: September 9, 2005, 10:38 pm
- Location: St-Eustache
King 700 jveut pas faire le smatte prend pas ca croche.... il faut que tu utilise le bon terme , rod end est pas trop explicite :wink:king 700 wrote:Salut mon dealer va les passer sur la garantie . Sur les honda ils ont toute eu un rappelle pour ses rod end pouri ses les meme rod end . Pourquoi suzuki ne font pas pareil.
Tu as les Tie rod , ca c'est la barre de metal avec des filets a chaque bout.
Tu as les inner tie rod end, ca c'est la piece visse sur la tie rod , cette piece a de la mobilite et se trouve vers l'interieur du VTT
Tu as les outer tie rod end , meme chose que les inner mais ils sont vers l'exterieur .
Tout ca juste pour faciliter la comprehension :)
Qui a dit que la vie était un fleuve tranquille ? ca fait que farme ta yeule pis rame stie....
-
king 700
- Posts: 95
- Joined: January 22, 2005, 4:12 pm
Salut homer , ce que je veux dire c'est les 4 tie rod intérieur et exterieur c'est 4 pareuil et il prenne toute du lousse cela veut dire qu'ils ont 5 millieme de lousse chaque au total 10 millieme chaque cote . Met ses 10 millieme au bout de la roue, chaque roue a du lousse de a peu près .5 pouce. Honda a eu le meme probleme avec ses tie rod il ont eu un rappelle.
merci.
merci.
-
king 700
- Posts: 95
- Joined: January 22, 2005, 4:12 pm
-
Homer
- Posts: 3030
- Joined: September 9, 2005, 10:38 pm
- Location: St-Eustache
Pour ceux qui lise l'Angla...trouver sur un Canadian forum
Suzuki just announced the are recalling some of the first '05 King Quads for outer tie-rods. During installation at the factory the tie-rod end boots may have been torn allowing dirt debris and water to enter the rubber cushion causing early wear and tear. It only affects a few VIN #'s That's great I'm not having problems with the ends. They should worry about the actual rods bending. Suzuki just announced this to the dealers today. The product up-date kits (recalls) will not be available to the U.S Dealers any earlier than October 17th 2005. Suzuki is calling this a voluntary Recall.
Suzuki just announced the are recalling some of the first '05 King Quads for outer tie-rods. During installation at the factory the tie-rod end boots may have been torn allowing dirt debris and water to enter the rubber cushion causing early wear and tear. It only affects a few VIN #'s That's great I'm not having problems with the ends. They should worry about the actual rods bending. Suzuki just announced this to the dealers today. The product up-date kits (recalls) will not be available to the U.S Dealers any earlier than October 17th 2005. Suzuki is calling this a voluntary Recall.
Qui a dit que la vie était un fleuve tranquille ? ca fait que farme ta yeule pis rame stie....
-
Connard101
- Posts: 421
- Joined: April 22, 2005, 8:50 pm
- Location: Saguenay (La Baie)
Et pour ceux qui ne sont pas forts en anglais... (S.V.P.) :wink:Homer wrote:Pour ceux qui lise l'Angla...trouver sur un Canadian forum
Suzuki just announced the are recalling some of the first '05 King Quads for outer tie-rods. During installation at the factory the tie-rod end boots may have been torn allowing dirt debris and water to enter the rubber cushion causing early wear and tear. It only affects a few VIN #'s That's great I'm not having problems with the ends. They should worry about the actual rods bending. Suzuki just announced this to the dealers today. The product up-date kits (recalls) will not be available to the U.S Dealers any earlier than October 17th 2005. Suzuki is calling this a voluntary Recall.
Yamaha Grizzly 700 2011 camo
Yamaha Kodiak 450 2009 camo (fille)
Suzuki King Quad 700 EFI 2005 rouge (vendu)
Polaris Explorer 400 1997 (vendu)
Suzuki QuadRunner 230 1990 (vendu)
Yamaha Kodiak 450 2009 camo (fille)
Suzuki King Quad 700 EFI 2005 rouge (vendu)
Polaris Explorer 400 1997 (vendu)
Suzuki QuadRunner 230 1990 (vendu)
-
Homer
- Posts: 3030
- Joined: September 9, 2005, 10:38 pm
- Location: St-Eustache
Rappel de quelque suzuki KQ . Seulement quelque numero de serie sont toucher. Les tie rod end aurait ete mal monter, les joints d'etancheite aurait ete mal installer et laisserais entre de la salete causant usure premature.Principalement au USAConnard101 wrote:Et pour ceux qui ne sont pas forts en anglais... (S.V.P.) :wink:Homer wrote:Pour ceux qui lise l'Angla...trouver sur un Canadian forum
Suzuki just announced the are recalling some of the first '05 King Quads for outer tie-rods. During installation at the factory the tie-rod end boots may have been torn allowing dirt debris and water to enter the rubber cushion causing early wear and tear. It only affects a few VIN #'s That's great I'm not having problems with the ends. They should worry about the actual rods bending. Suzuki just announced this to the dealers today. The product up-date kits (recalls) will not be available to the U.S Dealers any earlier than October 17th 2005. Suzuki is calling this a voluntary Recall.
Qui a dit que la vie était un fleuve tranquille ? ca fait que farme ta yeule pis rame stie....