code erreur pour arctic cat
Posted: March 3, 2011, 9:21 am
If you don't have the plug, jump the blue/red wire to black with a paper clip or similar object
ECU Error Codes
If a sensor fails or an out-of-tolerance signal is sensed by the ECU, an error code will be generated by the ECU. This will result in the analog needle swinging full scale. The EFI icon will flash.
To read the error code(s), use the following procedure:
1. Make sure the ignition switch is in the OFF position; then remove the seats.
2. Locate the diagnostic plug next to the PDM; then remove the black rubber cap.
3. Connect the Test Plug from Test Plug/Error Code List to the diagnostic plug.
4. Turn the ignition switch to the ON position and read the error code on the LCD. Refer to the following ECU Error Code List to identify the specific problem area.
ECU Error Code List
NOTE: Each of the following numerical codes will have a two-letter prefix. A prefix of AC (Active Code) or SC (Stored Code) will be displayed.
Always correct and clear Active Codes before clearing Stored Codes.
• 00 = No Fault Detected (active code only)
• 12 = CKP (Crankshaft Position) Sensor*
• 13 = APS (Air Pressure Sensor) - H1
• 13 = MAP (Manifold Absolute Pressure) Sensor - H2
• 14 = TPS (Throttle Position Sensor)
• 15 = ECT (Engine Coolant Temperature) Sensor
• 16 = Speed Sensor
• 21 = IAT (Inlet Air Temperature) Sensor
• 23 = Tilt Sensor*
• 24 = Ignition Coil #1*
• 26 = Ignition Coil #2* - H2
• 32 = Fuel Injector #1*
• 34 = Fuel Injector #2* - H2
• 40 = ISC (Idle Speed Control) Valve
• 41 = Fuel Pump Relay*
• 60 = Cooling Fan Relay
• 95 = Sensor Power
• 96 = Incorrect ECU*
• 97 = ECU Memory Power (constant battery power)
• 98 = ECU to Gauge Comm Link - H2
• 99 = Start/Run Not Possible (active code only)
*Will initiate code 99.
After all stored codes are cleared, clear the error code(s) using the following procedure.
NOTE: The ignition switch should be in the OFF position.
1. With the test plug connected to the diagnostic plug and the drive select switch in the 4WD position, hold the reverse override switch down and turn the ignition switch to the ON position.
2. After ten seconds, release the reverse override switch and turn the ignition switch to the OFF position; then turn the ignition switch to the ON position. The display should read AC00 (no fault detected).
NOTE: If the LCD still displays an error code, continue troubleshooting the appropriate component.
--------------------------------------------------------------------------------
ECU Error Codes
If a sensor fails or an out-of-tolerance signal is sensed by the ECU, an error code will be generated by the ECU. This will result in the analog needle swinging full scale. The EFI icon will flash.
To read the error code(s), use the following procedure:
1. Make sure the ignition switch is in the OFF position; then remove the seats.
2. Locate the diagnostic plug next to the PDM; then remove the black rubber cap.
3. Connect the Test Plug from Test Plug/Error Code List to the diagnostic plug.
4. Turn the ignition switch to the ON position and read the error code on the LCD. Refer to the following ECU Error Code List to identify the specific problem area.
ECU Error Code List
NOTE: Each of the following numerical codes will have a two-letter prefix. A prefix of AC (Active Code) or SC (Stored Code) will be displayed.
Always correct and clear Active Codes before clearing Stored Codes.
• 00 = No Fault Detected (active code only)
• 12 = CKP (Crankshaft Position) Sensor*
• 13 = APS (Air Pressure Sensor) - H1
• 13 = MAP (Manifold Absolute Pressure) Sensor - H2
• 14 = TPS (Throttle Position Sensor)
• 15 = ECT (Engine Coolant Temperature) Sensor
• 16 = Speed Sensor
• 21 = IAT (Inlet Air Temperature) Sensor
• 23 = Tilt Sensor*
• 24 = Ignition Coil #1*
• 26 = Ignition Coil #2* - H2
• 32 = Fuel Injector #1*
• 34 = Fuel Injector #2* - H2
• 40 = ISC (Idle Speed Control) Valve
• 41 = Fuel Pump Relay*
• 60 = Cooling Fan Relay
• 95 = Sensor Power
• 96 = Incorrect ECU*
• 97 = ECU Memory Power (constant battery power)
• 98 = ECU to Gauge Comm Link - H2
• 99 = Start/Run Not Possible (active code only)
*Will initiate code 99.
After all stored codes are cleared, clear the error code(s) using the following procedure.
NOTE: The ignition switch should be in the OFF position.
1. With the test plug connected to the diagnostic plug and the drive select switch in the 4WD position, hold the reverse override switch down and turn the ignition switch to the ON position.
2. After ten seconds, release the reverse override switch and turn the ignition switch to the OFF position; then turn the ignition switch to the ON position. The display should read AC00 (no fault detected).
NOTE: If the LCD still displays an error code, continue troubleshooting the appropriate component.
--------------------------------------------------------------------------------