pick-up ???
-
Pascal la Dalle
- Posts: 758
- Joined: September 16, 2005, 9:42 pm
- VTT: ranger 800 xp
- Location: Dupuy
-
Le Proprio
- Posts: 8
- Joined: January 27, 2011, 7:42 pm
- VTT: Aucun
- Location: Amos
Re: pick-up ???
Je suis mécano et je te dirais regarde pour ton/tes cataliseur .Ca arrive qu'ils se bloque ou qu'il se défasse.Ca manque de puissance et ca marche au gaz.
- Kerosen
- Posts: 9026
- Joined: October 5, 2002, 2:03 pm
- VTT: A voir
- Location: Carignan
Re: pick-up ???
Le Proprio wrote:Je suis mécano et je te dirais regarde pour ton/tes cataliseur .Ca arrive qu'ils se bloque ou qu'il se défasse.Ca manque de puissance et ca marche au gaz.
La temperature moteur augmente aussi ?
Kerosen
-
Le Proprio
- Posts: 8
- Joined: January 27, 2011, 7:42 pm
- VTT: Aucun
- Location: Amos
Re: pick-up ???
La température moteur (cadran ) ne monte pas plus.Si ca serait spécifique à un cylindre je dirais que ca pourrait être un injecteur.Ca pourrait aussi être un ground de l'ECM corrodé.Quand ca touche tout les cylindres et que le moteur manque beaucoup de puissance ,je pense toujours au cataliseur.Ce n'ai peut-être pas ca mais c'est juste une idée.
-
Patman
- Site Admin
- Posts: 19151
- Joined: February 27, 2006, 10:13 am
- VTT: Kodiak 400
- Location: Ancienne-Lorette
Re: pick-up ???
Mais un catalyseur qui est bouché ça fait de la restriction et fait chauffer le moteur :?
Patman
Kodiak 400 / 2000
GMC Sierra 2003 / 4p/6litres
Glastron Gt 205, 4.3L, 190 hp, 2007 , Vendu
Monterey 282, 31', 2 x 5,0 litres MPI de 270 hp chaque
Garmin276C
Kodiak 400 / 2000
GMC Sierra 2003 / 4p/6litres
Glastron Gt 205, 4.3L, 190 hp, 2007 , Vendu
Monterey 282, 31', 2 x 5,0 litres MPI de 270 hp chaque
Garmin276C
- Kerosen
- Posts: 9026
- Joined: October 5, 2002, 2:03 pm
- VTT: A voir
- Location: Carignan
Re: pick-up ???
Le Proprio wrote:La température moteur (cadran ) ne monte pas plus.Si ca serait spécifique à un cylindre je dirais que ca pourrait être un injecteur.Ca pourrait aussi être un ground de l'ECM corrodé.Quand ca touche tout les cylindres et que le moteur manque beaucoup de puissance ,je pense toujours au cataliseur.Ce n'ai peut-être pas ca mais c'est juste une idée.
mais dans le cas d'un ground corroder sa donnerais comme code ''Injector ground low voltage''
Kerosen
-
Le Proprio
- Posts: 8
- Joined: January 27, 2011, 7:42 pm
- VTT: Aucun
- Location: Amos
Re: pick-up ???
Check Engine Light Code P0300
Random/Multiple Cylinder Misfire Detected
Description:
How does a P0300 code trigger the check engine light? This code will trigger the check engine light as follows:
The misfire detection monitor, a software strategy built into the computer, is designed to detect an engine misfire. The computer can also normally identify the specific cylinder in which the misfire has occurred. A misfire is nothing more than a lack of combustion, which can be caused by poor fuel quality or metering, low compression, lack of spark or unmetered air entering the engine. There are other possible, less obvious causes as well, such as uncommanded Exhaust Gas Recirculatin (EGR), flow. When the misfire monitor detects a misfire, it will trigger the check engine light with the specific cylinder number as the last digit in the P030X code. For instance cylinder 1 misfire is P0301, cylinder 2 is P0302 etc. In this case we have either multiple cylinders misfiring, or the computer simply can't determine the specific cylinder, and as such we are left with the P0300 in computer memory.
See also: P0300 diagnostic code @ OBD-Codes.com
Possible Causes:
Fuel injectors, related wiring, sensors and computer issues
Running out of gas, or poor fuel quality
Evaporative emissions system (EVAP) concerns: fuel vapors leaking into engine
Incorrect Fuel Pressure
EGR system concerns: leaking EGR valve or restricted ports
Base engine concerns: low compression, valve train problems and timing issues
Ignition system concerns including, but not limited to:
Faulty spark plugs
Faulty coil or related wiring
Ignition module or related wiring issues
Ignition related sensor faults or wiring issues
Diagnostic Help:
To diagnose a P0300 trouble code we begin by checking for proper fuel and ignition system operation, and then follow up with the less likely causes listed above, such as EGR and EVAP system problems. New style coil on plug applications have a high failure rate, and can be concluded faulty by swapping to another cylinder and checking to see if the misfire moves to that cylinder. This is a quick check if a capable scan tool or oscilloscope is not available. Always make sure the basic maintenance is done first and that things such as the fuel filter, air filter, spark plugs and spark plug wires are in good working order, as these are all possible candidates for a problem. If necessary, check for wiring and component concerns. See our article Automotive Circuit Testing 101, if you need more assistance with this. If concern is determined to be intermittent, check out our article on intermittent diagnosis and wiggle test connectors and wiring, attempting to duplicate concern. You may also use the "Get Help" link if you need specifications or have any other related questions. Remember to refer to an appropriate manual for specific instruction.
Random/Multiple Cylinder Misfire Detected
Description:
How does a P0300 code trigger the check engine light? This code will trigger the check engine light as follows:
The misfire detection monitor, a software strategy built into the computer, is designed to detect an engine misfire. The computer can also normally identify the specific cylinder in which the misfire has occurred. A misfire is nothing more than a lack of combustion, which can be caused by poor fuel quality or metering, low compression, lack of spark or unmetered air entering the engine. There are other possible, less obvious causes as well, such as uncommanded Exhaust Gas Recirculatin (EGR), flow. When the misfire monitor detects a misfire, it will trigger the check engine light with the specific cylinder number as the last digit in the P030X code. For instance cylinder 1 misfire is P0301, cylinder 2 is P0302 etc. In this case we have either multiple cylinders misfiring, or the computer simply can't determine the specific cylinder, and as such we are left with the P0300 in computer memory.
See also: P0300 diagnostic code @ OBD-Codes.com
Possible Causes:
Fuel injectors, related wiring, sensors and computer issues
Running out of gas, or poor fuel quality
Evaporative emissions system (EVAP) concerns: fuel vapors leaking into engine
Incorrect Fuel Pressure
EGR system concerns: leaking EGR valve or restricted ports
Base engine concerns: low compression, valve train problems and timing issues
Ignition system concerns including, but not limited to:
Faulty spark plugs
Faulty coil or related wiring
Ignition module or related wiring issues
Ignition related sensor faults or wiring issues
Diagnostic Help:
To diagnose a P0300 trouble code we begin by checking for proper fuel and ignition system operation, and then follow up with the less likely causes listed above, such as EGR and EVAP system problems. New style coil on plug applications have a high failure rate, and can be concluded faulty by swapping to another cylinder and checking to see if the misfire moves to that cylinder. This is a quick check if a capable scan tool or oscilloscope is not available. Always make sure the basic maintenance is done first and that things such as the fuel filter, air filter, spark plugs and spark plug wires are in good working order, as these are all possible candidates for a problem. If necessary, check for wiring and component concerns. See our article Automotive Circuit Testing 101, if you need more assistance with this. If concern is determined to be intermittent, check out our article on intermittent diagnosis and wiggle test connectors and wiring, attempting to duplicate concern. You may also use the "Get Help" link if you need specifications or have any other related questions. Remember to refer to an appropriate manual for specific instruction.
-
Le Proprio
- Posts: 8
- Joined: January 27, 2011, 7:42 pm
- VTT: Aucun
- Location: Amos
Re: pick-up ???
SymptomsSymptoms may include:
•the engine may be harder to start
•the engine may stumble / stumble, and/or hesitate
•other symptoms may also be present
CausesA code P0300 may mean that one or more of the following has happened:
•Faulty spark plugs or wires
•Faulty coil (pack)
•Faulty oxygen sensor(s)
•Faulty fuel injector(s)
•Burned exhaust valve
•Faulty catalytic converter(s)
•Stuck/blocked EGR valve / passages
•Faulty camshaft position sensor
•Defective computer
Possible SolutionsIf there are no symptoms, the simplest thing to do is to reset the code and see if it comes back.
If there are symptoms such as the engine is stumbling or hesitating, check all wiring and connectors that lead to the cylinders (i.e. spark plugs). Depending on how long the ignition components have been in the car, it may be a good idea to replace them as part of your regular maintenance schedule. I would suggest spark plugs, spark plug wires, distributor cap, and rotor (if applicable). Otherwise, check the coils (a.k.a. coil packs). In some cases, the catalytic converter has gone bad. If you smell rotten eggs in the exhaust, your cat converter needs to be replaced. I've also heard in other cases the problems were faulty fuel injectors.
Random misfires that jump around from one cylinder to another (read: P030x codes) also will set a P0300 code. The underlying cause is often a lean fuel condition, which may be due to a vacuum leak in the intake manifold or unmetered air getting past the airflow sensor, or an EGR valve that is stuck open.
•the engine may be harder to start
•the engine may stumble / stumble, and/or hesitate
•other symptoms may also be present
CausesA code P0300 may mean that one or more of the following has happened:
•Faulty spark plugs or wires
•Faulty coil (pack)
•Faulty oxygen sensor(s)
•Faulty fuel injector(s)
•Burned exhaust valve
•Faulty catalytic converter(s)
•Stuck/blocked EGR valve / passages
•Faulty camshaft position sensor
•Defective computer
Possible SolutionsIf there are no symptoms, the simplest thing to do is to reset the code and see if it comes back.
If there are symptoms such as the engine is stumbling or hesitating, check all wiring and connectors that lead to the cylinders (i.e. spark plugs). Depending on how long the ignition components have been in the car, it may be a good idea to replace them as part of your regular maintenance schedule. I would suggest spark plugs, spark plug wires, distributor cap, and rotor (if applicable). Otherwise, check the coils (a.k.a. coil packs). In some cases, the catalytic converter has gone bad. If you smell rotten eggs in the exhaust, your cat converter needs to be replaced. I've also heard in other cases the problems were faulty fuel injectors.
Random misfires that jump around from one cylinder to another (read: P030x codes) also will set a P0300 code. The underlying cause is often a lean fuel condition, which may be due to a vacuum leak in the intake manifold or unmetered air getting past the airflow sensor, or an EGR valve that is stuck open.
-
marco5
- Posts: 281
- Joined: January 14, 2009, 12:34 pm
- VTT: honda foreman 4
Re: pick-up ???
Pascal la Dalle wrote:on dirais que j`ai pu overdrive ????
en fin de compte a tu réglé ton ou tes problèmes
cliss au printemps quand j'ai déremiser le mien un 4.3 1997 j'ai eu toute les même problemes que toi
-
Pascal la Dalle
- Posts: 758
- Joined: September 16, 2005, 9:42 pm
- VTT: ranger 800 xp
- Location: Dupuy
Re: pick-up ???
caline j`en ai des chose a regardé ... un gros merci pour les info . et non je n`ai pas trouver le problème . mais je cherche toujours .
-
Pascal la Dalle
- Posts: 758
- Joined: September 16, 2005, 9:42 pm
- VTT: ranger 800 xp
- Location: Dupuy
Re: pick-up ???
sa ce peux tu que ce serais ma pompe a gaz qui aurais pas assez de pression ???
- Kerosen
- Posts: 9026
- Joined: October 5, 2002, 2:03 pm
- VTT: A voir
- Location: Carignan
Re: pick-up ???
Pascal la Dalle wrote:sa ce peux tu que ce serais ma pompe a gaz qui aurais pas assez de pression ???
a ma conaissance non car il a un capteur de pression et il l'aurait indiquer
Kerosen
-
marco5
- Posts: 281
- Joined: January 14, 2009, 12:34 pm
- VTT: honda foreman 4
Re: pick-up ???
salut pascal
j'ai eu pas mal toute les même problème que toi
moi le mien je l'avais remisée l'hiver passé, quand je l'ai sorti au printemps c'allait pas bien,je pensait condensation dans tank a gaz ,de l'eau j'ai mit une couple de gaz line ça aider,mais le bockage revenait , j'ai penser a la pompe a gaz aussi , mais avant de commencer a changer ben des morceaux j'ai été au plus simple le filtre au gaz , pi en même temps moi aussi quand c'était humide c'était pire ,je l'ai vérifier un soir a la noirceur pour me rende compte que le feu sautait du fil qui ploque au coil , j'ai mit du silicone diélectrique ,ça régler le prob.
mais quand j'ai changer mon filtre a gaz (j'ai couper le tuyau en le défesant, que j'ai réparé)) il cé mit a super bien aller ????????? j'ai trouver ça vraiment bizzare q'un filtre a gaz puisse faire tant de prob.
y me reste toujours un problème quand le moteur est froid y tire pas pentoute ça y prend un bon 5 a 10 minute avant qu'il alle bien ,je roule max 60 km on dirait que le moteur ne le prend plu et si je le tien pour le forcer le moteur vien bouillant en clissssss?
ya un mécano qui fait du gm qui m'a deja dit que le prob. se situait en dessous du distributeur?que c'était une faiblesse des 4.3 ?
j'ai eu pas mal toute les même problème que toi
moi le mien je l'avais remisée l'hiver passé, quand je l'ai sorti au printemps c'allait pas bien,je pensait condensation dans tank a gaz ,de l'eau j'ai mit une couple de gaz line ça aider,mais le bockage revenait , j'ai penser a la pompe a gaz aussi , mais avant de commencer a changer ben des morceaux j'ai été au plus simple le filtre au gaz , pi en même temps moi aussi quand c'était humide c'était pire ,je l'ai vérifier un soir a la noirceur pour me rende compte que le feu sautait du fil qui ploque au coil , j'ai mit du silicone diélectrique ,ça régler le prob.
mais quand j'ai changer mon filtre a gaz (j'ai couper le tuyau en le défesant, que j'ai réparé)) il cé mit a super bien aller ????????? j'ai trouver ça vraiment bizzare q'un filtre a gaz puisse faire tant de prob.
y me reste toujours un problème quand le moteur est froid y tire pas pentoute ça y prend un bon 5 a 10 minute avant qu'il alle bien ,je roule max 60 km on dirait que le moteur ne le prend plu et si je le tien pour le forcer le moteur vien bouillant en clissssss?
ya un mécano qui fait du gm qui m'a deja dit que le prob. se situait en dessous du distributeur?que c'était une faiblesse des 4.3 ?
-
Pascal la Dalle
- Posts: 758
- Joined: September 16, 2005, 9:42 pm
- VTT: ranger 800 xp
- Location: Dupuy
Re: pick-up ???
j`ai les codes ...
P0300
P0108
P0121
P0122
P0106
P0430
P1345
P0106
et mon chum m`a dit de checker mes catalyseur .....
P0300
P0108
P0121
P0122
P0106
P0430
P1345
P0106
et mon chum m`a dit de checker mes catalyseur .....
- bearcat
- Posts: 4722
- Joined: May 6, 2005, 6:23 am
- VTT: commander 800
- Location: Mauricie
Re: pick-up ???
J,ai eu un 4.3 1997 et il boquais faque quand je changeais le cap distributeur il etais correct pour un 1000 kil. et recommencais.J,ai changer le distributeur aux complet pour un en aluminiume que j'ai pris sur e'bay et le problem c,est corriger.
Ancienement RON53- Outlander 2006 vendu un outlander max xt 2009 800R vendu,pare brise BRP,coffre quadrax,Coffre avant moose,ressort heavy duty avant,clutch cvtech,frame renforcie,GPS garmin 76cx.Maintenant avec un can am commander 2012.